S/P DIF ( s/pdif )

s/pdif цифровой выход
SPDIF – много мы знаем “о нем”. Sony/Philips Digital Interconnect Format. Замеxательная статья с сайта Epanorama, обязательна к прочтению для понимания сути цифровой передачи. Если затруднительн читать на английском, пробуйте воспользоваться переводчиком от гугл или любым другим удобным вам.

History

Since the early 80’s, a step towards digital audio has been set by the introduction of the Compact Disc player. In the beginning, those signals stayed inside the set, and were converted to analog signals before leaving the cabinet. A new trend is to keep signals into the digital domain as long as possible, because this is the only way to keep the signal quality. To make this possible different devices must be able communicate with one another within the digital domain. Several interfaces exist to perform such tasks, from which one has grown to the audio standard worldwide: IEC958 1989-03 (consumer Part) from the EBU. In Japan an equivalent EIAJ CP-340 1987-9 is standard.

Characteristics

Standard IEC958 “Digital audio interface” from EBU (European
Broadcasting Union) details:

  • Audio format : linear 16 bit default, up to 24 bit expandable
  • Allowed sampling frequencies (Fs) of the audio:
    • 44.1kHz from CD
    • 48 kHz from DAT
    • 32 kHz from DSR
  • One way communication: from a transmitter to a receiver.
  • Control information:
    • V (validity) bit : indicates if audio sample is valid.
    • U (user) bit : user free coding i.e. running time song, track number.
    • C (channel status) bit : emphasis, sampling rate and copy permit.
    • P (parity) bit : error detection bit to check for good reception.
  • Coding format: biphase mark except the headers (preambles), for sync purposes.
  • Bandwidth occupation : 100kHz up to 6Mhz (no DC!)
  • Signal bitrate is 2.8Mhz (Fs=44.1kHz), 2Mhz (Fs=32kHz) and 3.1Mhz (Fs=48kHz).

Physical connection:

  • Cable: 75ohm +/-5% (l<10m) or 75ohm +/-35% (l>10m)
  • Line driver:
    • Zout: 75ohm +/-20% (100kHz .. 6Mhz)
    • Vout: 0.4Vpp .. 0.6Vpp, <0.05Vdc (75ohm terminated)
  • Line receiver:
    • Zin: 75ohm +/-5%
    • Vin: 0.2Vpp .. 0.6Vpp

The interface

IEC958 is a newer standard which supersedes AES/EBU and also S-PDIF.
The S/PDIF interface (IEC-958) is a ‘consumer’ version of the
AES/EBU-interface. The two
formats are quite compatible with each other, differing only in the subcode
information and connector. The professional format subcode contains ASCII
strings for source and destination identification, whereas the commercial
format carries the SCMS.

Here is a short comparision table of AES/EBU and S/PDIF interfaces:

                          AES/EBU              S/PDIF (IEC-958)

Cabling 110 ohm shileded TP 75 ohm coaxial or fiber
Connector 3-pin XLR RCA (or BNC)
Signal level 3..10V 0.5..1V
Modulation biphase-mark-code biphase-mark-code
Subcode information ASCII ID text SCMS copy protection info
Max. Resolution 24 bits 20 bits (24 bit optional)

NOTE: AES/EBU also exists in 75 ohm/BNC version (AES-3id-1995 standard).
75 ohm BNC version of AES/EBU is very electrically similar to
75 ohm coaxial S/PDIF shown above.

The electrical characteristics of AES/EBU are based on on RS-422,
so basically any differential RS-422 chip will do as
the receiver and transmitter chips. S/PDIF coaxial interface is not
specificaly based on any other standard I know of
(but is quite similar in signal levels and bandwidth requrements
to some video signals).

Both S/PDIF and AES/EBU can, and do transfer 24 bit words. In AES/EBU,
the last 4 bits have a defined usage, so if anyone puts audio in there,
it has to go to something that doesn’t expect the standard specifies.
But in S/PDIF, there’s nothing that says what you have to use the bits
for, so filling them all up with audio is acceptable.
Typical S/PDIF equipments only use 16 or 20 bit resolutions.
While many equipments use more than 16 bits in internal processing,
it’s not unusual for the output to be limited to 16 bits.

Note on HDR-2 (2 pin header) interface used in some PC products:

Many modern PC CD-ROM drives and some soundcards (SB32, AWE32, etc.)
have a two pin digital output connector
in the back of the drive and they sometimes call that interface
S/PDIF. Unfortunately the electrical signal which comes from it is not
exactly what is described in S/PDIF specifications. The data format
is exactly the same, but the signal is TTL level (5Vpp) signal instead
of the normal 1Vpp signal. The output level might be selected to
make the interfacing to other digital electronics easy when signal
is travelling inside the computer (the normal output driver system
and input amplifiers can be avoided). The downnside of this is
that you need to build some electronics to make the signal from
the CD-ROM drive to match what normal S/PDIF equipments expect.

Multi channel audio and S/PDIF

IEC958 was named IEC60958 at 1998.
IEC60958 (The S/PDIF) can carry normal audio and IEC61937 datastreams.
IEC61937 datastreams can contain multichannel sound like MPEG2, AC3 or DTS.
When IEC61937 datastrams are transferred, the bits which normally carry audio
samples are replaced with the databits from the datastream and the
headers of the S/PDIF signal. Channel-status information contains
one bit (but 1) which tells if the data in S/PDIF frame is digital
audio or some other data (DTS, AC3, MPEG audio etc.). This bit
will tell normal digital audio equipments that they don’t try to play
back this data as they were audio samples.
(would sound really horrible if this happens for some reason).

The equipments which can handle both normal audio and
IEC61937 just look at those header bits to determine what to do with
the received data.

Cabling details

S/PDIF (IEC-958) uses 75 ohm coaxial cable and RCA connectors.
75 ohm coaxial cable is inexpensive, because it is the same cable
as used in video transmission (you can buy a video cable with
RCA connectors to connect you S/PDIF equipments together).
Coaxial S/PDIF connections work typically at least to
10-15 meter distances with good 75 ohm coaxial cable.

AES/EBU-interface uses the well known symmetrical connections with
transformer isolation and an output impedance of 110 ohm. The signal-level
of this interface is reasonably higher than in the consumer version (3…10
volts).
Because AES/EBU digital audio signals are transmitted at high, video-like
frequencies (at around 6MHz) and should be handled very differently than
standard analog audio lines.
Commonly used XLR-3 microphone cables have various impedance ratings
(30 ohm to 90 ohm typical) and exhibit poor digital transmission performance.
The result is signal drop out and reduced cable lengths due to severe
impedance mis-matching (VSWR) between AES/EBU 110 ohm equipment.
AES/EBU signal transmission work for few tens of meters with a good cable.

There also an optical version of S/PDIF interface which is usually
called Toslink, because uses Toslink optical components.
The transmission media is 1 mm plastic fiber and the signals are
trasmitted using visible light (red transmitting LED). The optical
signals have exactly the same format as the electrical S/PDIF signals,
they are just converted to light signals (light on/off).
Because high light signal attenuation in the Toslink fiberoptic
cable, the transmission distance available using this technique
is less than 10 meters (with some equipments only few meters).

What can make difference in the sound of digital signal ?

There are two things which can cause differences between the sound of
digital interfaces:

1. Jitter (clock phase noise)

This really only affects sound of the signal going directly to a DAC.
If you’re running into a computer, the computer is effectively going to
be reclocking everything. Same applies also to CD-recoders, DAT tape
decs and similar devices. Even modern DACs have typically a small
buffer and reclocking circuitry, so the jitter is not so big problem
nowadays that it used to be.

2. Errors

This usually causes very significant changes in the sound, often loud
popping noises but occasionally less offensive effects. Any
data loss or errors in either are a sign of a very broken link which is
probably intermittently dropping out altogether.

S/PDIF signals

The signal on the digital output of a CD-player looks like almost
perfect sine-wave, with an amplitude of 500 mVtt and a frequency of almost
3 MHz.

For each sample, two 32-bit words are transmitted, which results in a
bit-rate of:

    2.8224 Mbit/s  (44.1 kHz samplingrate, CD, DAT)
    3.072  Mbit/s  (48 kHz sampling rate, DAT)
    2.048  Mbit/s  (32 kHz sampling rate, for satellite purposes)

The output impedance is standard 75 ohm, so ordinary coaxial cable designed
for video applications can be used.
The minimal input level of S/PDIF interface is 200 mVtt which allows
some cable losses. There is no real need for special quality cable
as long as the cable is made of 75 ohm coaxial cable (a good video accessory
cable works also as good S/PDIF cable).

The Coding Format

The digital signal is coded using the ‘biphase-mark-code’ (BMC), which is a
kind of phase-modulation. In this system, two zero-crossings of the signal
mean a logical 1 and one zero-crossing means a logical 0.

                _   _   _   _   _   _   _   _   _   _   _   _
               | | | | | | | | | | | | | | | | | | | | | | | |
clock   0 ___ _| |_| |_| |_| |_| |_| |_| |_| |_| |_| |_| |_| |_

___ _______ ___ ___
| | | | | | | |
data 0 ___ _| |_______| |___| |_______| |___
signal 1 0 0 1 1 0 1 0 0 1 0

_ ___ _ _ ___ _ ___ _
Biphase | | | | | | | | | | | | | | | |
Mark 0 ___ | | | | | | | | | | | | | | | |
signal | | | | | | | | | | | | | | | |
_| |_| |___| |_| |_| |_| |___| |_| |___

cells 1 0 1 1 0 0 1 0 1 0 1 1 0 1 0 0 1 1 0 1 0 0

The frequency of the clock if twice the bitrate. Every bit of the original
data is represented as two logical states, which, together, form a cell.
The length of a cel (‘time-slot’) is equal to the length of a databit. The
logical level at the start of a bit is always inverted to the level at the
end of the previous bit. The level at the end of a bit is equal (a 0
transmitted) or inverted (a 1 transmitted) to the start of that bit.

The first 4 bits of a 32-bit word (bits 0 through 3) form a preamble which
takes care of synchronisation. This sync-pattern doesn’t actually carry
any data, but only equals four databits in length. It also doesn’t use the
BMC, so bit patterns which include more than two 0’s or 1’s in a row can
occur (in fact, they always do).

There are 3 different sync-patterns, but they can appear in different
forms, depending on the last cell of the previous 32-bit word (parity):

   Preamble    cell-order         cell-order
       (last cell "0")    (last cell "1")
   ----------------------------------------------
   "B"         11101000           00010111
   "M"         11100010           00011101
   "W"         11100100           00011011

Preamble B: Marks a word containing data for channel A (left)
at the start of the data-block.

Preamble M: Marks a word with data for channel A that isn’t
at the start of the data-block.

Preamble W: Marks a word containing data for channel B.
(right, for stereo). When using more than 2
channels, this could also be any other channel
(except for A).

Word and Block Formats

Every sample is transmitted as a 32-bit word (subframe).
These bits are used as follows:

   bits           meaning
   ----------------------------------------------------------
   0-3            Preamble (see above; special structure)

4-7 Auxillary-audio-databits

8-27 Sample
(A 24-bit sample can be used (using bits 4-27).
A CD-player uses only 16 bits, so only bits
13 (LSB) to 27 (MSB) are used. Bits 4-12 are
set to 0).

28 Validity
(When this bit is set, the sample should not
be used by the receiver. A CD-player uses
the ‘error-flag’ to set this bit).

29 Subcode-data

30 Channel-status-information

31 Parity (bit 0-3 are not included)

The number of subframes that are used depends on the number of
channels that is transmitted. A CD-player uses Channels A and B
(left/right) and so each frame contains two subframes.
A block contains 192 frames and starts with a preamble “B”:

"M" Ch.1 "W" Ch.2 "B" Ch.1 "W" Ch.2 "M" Ch.1 "W" Ch.2 "M" ...

| ||_ sub __|_ sub _|| |
| || || |
|__ Frame 191 ___||__ Frame 0 ___||__ Frame 1 ____|

|
block-start

Channelstatus and subcode information

In each block, 384 bits of channelstatus and subcode info are transmitted.
The Channel-status bits are equal for both subframes, so actually only 192
useful bits are transmitted:

   bit            meaning
   -------------------------------------------------------------
   0-3            controlbits:

bit 0: 0 (is set to 1 during 4 channel transmission)
bit 1: 0=Digital audio, 1=Non-audio (reserved to be 0 on old S/PDIF specs)
bit 2: copy-protection. Copying is allowed
when this bit is set.
bit 3: is set when pre-emphasis is used.

4-7 0 (reserved)

9-15 catagory-code:

0 = common 2-channel format
1 = 2-channel CD-format
(set by a CD-player when a subcode is
transmitted)
2 = 2-channel PCM-encoder-decoder format

others are not used

19-191 0 (reserved)

The subcode-bits can be used by the manufacturer at will.
They are used in blocks of 1176 bits before which a
sync-word of 16 “0”-bits is transmitted

Electrical Interface

The electrical interface for S/PDIF signals can be either
75 ohm coaxial cable or optical fiber (usually called Toslink).
Usually consumer models use
that coaxial cable interface and semiprofessional/professional
equipments use optical interface. The electrical signal in the
coaxial cable is about 500mVtt.


Converting between AES/EBU and S/PDIF interfaces

There are differences in the electrical characteristics of AES/EBU and S/PDIF
interfaces:

  • AES/EBU uses a balanced differential line based on XLR connectors and the signal levels are 5 volts
  • S/P-DIF uses a coaxial unbalanced line with RCA connectors and the signal levels are around 0.5 volts

You can convert one electrical interface to another with
a small amount of off-the-shelf hardware and a little time
as you can see in the circuit below.

But the protocol used in AES/EBU and S/PDIF is not exactly the same
and that can cause sometimes problems.
The basic data format of AES and S/P-DIF are identical. There is a bit
in the channel status frame that tells which is which. Depending upon
the setting of that bit, some bits have different meanings. For
example, the bits used to describe de-emphasis in the AES/EBU protocol
overlap the bits used to implement the SCMS protocol in S/P-DIF land.

The big problem comes in the fact that MANY products out there are VERY
picky about what they see in the bits, and even though a given signal may
fall within the letter of the standard, some equipment will absolutely
refuse to talk to it. Many equipments are reasonably flexible and
tolerant of slight foos in the signal so the simple converters cna work on
those. But a simple converter that works
fine with one piece will as likely not work with another.

What are different types of IEC 958-interface

There are 2 implementations of IEC 958: consumer and professional.
Those are referred in standard as IEC958 Types I and II.
IEC958 professional format is same as AES/EBU but is carried over
same type of coaxial or optical interface as consumer S/PDIF.
IEC958 consumer format is the S/PDIF format used in CD-players.
You can put an S-PDIF data stream on an AES/EBU physical balanced cable,
or vice versa, and still have it be valid IEC958 data.
Professional and consumer formats (Types I and II) differ only in the subcode
information. In order to do track indexing, you must have a consumer
format data stream (ie. an S/PDIF style data).

Jitter specifications of AES/EBU interface

The AES/EBU standard for serial digital audio uses typically 163 ns clock rate
and allows up to +-20 ns of jitter in the signal. This peaks to peak value of
40 ns is aroun 1/4 of the unit interval. D/A conversion clock jitter requirements
are considrably tighter. A draft AES/EBU standard specifies the D/A converter clock
at 1 ns jitte; however, a theoretical value for 16-bit audio could be as small
as 0.1 nsec. Small jitter D/A conversion is implemented by using separate PLL
clocks for data recover and DAC and by using a buffering between data recovery and
DAC.

Conversion circuits

Here are some AES/EBU and S/PDIF circuit collected from various sources.
The following circuit will only convert the signal levels, not other protocol
details.

Remeber that although the audio data is the same in both AES/EBU and S/PDIF
interfaces, they are indeed different formats, at least in their subcode.
AES converted to coax is NOT S/PDIF, and S/PDIF converted to XLR
balanced is NOT AES. They are still their native format, just the transmission
medium has changed. Whether they will work in your application depends on the
equipment chosen.

Some DATs have a switch that selects one format or the other regardless
of the physical interface, some just ignore what they don’t understand
(usually resulting in the generally positive benefit of ignoring SCMS
encoding), and some indeed gag on the “other” format. But simply fixing
the physical interface works far more often than it doesn’t.

How to do different conversions using the circuit below

Here are some ideas how to make the most common conversions using
the circits described below. Note: there is no guarantee that the
information in this or the circuit are correct (they are believed to
be correct but note tested by the author).

  • AES/EBU to S/PDIF: There is complete circuit for this
  • S/PDIF to AES/EBU: There is complete circuit for this
  • S/PDIF to optical: S/PDIF coax input circuit followed with optical TOSLINK output
  • Optical to S/ODIF: Optical TOSLINK receiver followed with S/PDIF output buffer circuit
  • CD-ROM digital output to normal S/PDIF: S/PDIF output buffer circuit does this
  • CD-ROM digital output to optical: Connect optical TOSLINK output circuit to CD-ROM output

For every other conversion combination you can think of you can find
circuits on the lis below. To build an dapter you need two parts
connected after each other.

  • First you need an input circuit which converts the input you want (coax,optical or AES/EBU) to TTL format (if the input is in TTL format you don’t need any input circuitry)
  • Connect a suitable output circuit with TTL input after the receiving electronics to give you the output format you want (coax,optical,AES/EBU,TTL)

After you have slected the suitable circuit parts, built them an attached
them together you get the conversion circuit you want. If you need
more than one output, you can connect few (1-4) output modules to one
input circuitry to have more then one output.

AES/EBU to S/PDIF signal level converter

AES out:   2-------330 ohm-----+-------------   SPDIF in
                               |
           3--+              91 ohm
              |                |
           1--+------+---------+-------------
                     |
                     -
                ground

The idea for this circuit is taken from articles posted to Usenet News.

If you are looking for a professional components for 110 ohm to 75 ohm
interconnection then check
Canare web site where they have
110 OHM-75 OHM IMPEDANCE TRANSFORMERS.

S/PDIF to AES/EBU

                                           _
                  + 5 volt                | \
SPDIF out:          |                   +-|  O-+
                    _ +--4,7k-+         | |_/  |
              diode ^ |  _    |     _   |  _   |
       10 u (+)     | | | \   |    | \  | | \  |      100 n
O--+--+-||-+--------+-+-|  O--+--+-|  O-+-|  O-+-120 r-||-+----+-- 2
   |  |    |        |   |_/   |  | |_/    |_/             |    |
   |  +-||-+ 100n   _       2,2k |                       1 k   |
  75r               ^ diode   |  |     IC                 |    |   AES in
   |                |        --- |                       ---   |
  ---              ---           |       _                    220r
                                 |      | \           100 n    |
                                 +--+---|  O---+--120 r-||-+---+--- 3
 Diode = 1N914 or 1N4148            |   |_/    |           |
                                    |    _     |         1 k   +--- 1
                                    |   | \    |           |   |
    IC = 74HC04 or CMOS 4049        +---|  O---+          --- ---
                                        |_/

 


The idea for this circuit is taken from articles posted to Usenet News.


S/PDIF conversion circuit building blocks

This is a collection of S/PDIF circuits found from various sources.
The circuits are presented as building blocks which have one end
on S/PDIF standard signal and other end an TTL level signal.
The TTL levle signal end of the circuits is designed to be the
the interface which you can use to wire different modules
together to make whatever S/PDIF converter circuit you want.
The circuit are presented as building blocks because with this
approacs you can most easily build a suitable circuit for
all conversion needs.

Here are tips for building a conversision circuits for
different uses:

  • Coaxial S/PDIF to optical: Select any S/PDIF coaxial input circuit and connect it’s TTL output to one optical S/PDIF (Toslink) output circuit.
  • Optical S/PDIF to coaxial: Select one optical S/PDIF input circuit and connet it’s TTL output to any coaxial S/PDIF output circuit.
  • CD-ROM digital out to coaxial: CD-ROMs output TTL level S/PDIF, so get it to caoxial you just need a coaxial output circuit where you directly connect the digital signal from your CD-ROM drive.

For other conversion needs do a little thinking and you should
find quite easily the answer what blocks to connect to each other.

S/PDIF output buffer circuits

Here is set of output circuit which take in TTL level S/PDIF signal
in and output standard S/PDIF coax cable output signal. Those
output circuit are very useful building blocks for all kinds
of S/PDIF related electronics projects. All the circuits do
basically the same thing. They just use different components,
so use the one where uou can easily get components.

S/PDIF output buffer circuit

                                                          S/PDIF output
                                                          (RCA or BNC)
                            |\
TTL level signal -----+-----| O-----680R--+---------+    +------- center pin
                      |     |/            |         |    |
                      |                   |          )||(
                      |     |\            |          )||(
                      +-----| O-----680R--+          )||(
                            |/            |          )||(
                                        100R        |    |
                          74HC04          |         |    +------- ground
                                          +----+----+ T1
                                               |
                                              ---

 


Idea for this circuit is taken from
“A digital Output for the CD720” web page (was at http://www.spiceisle.com/homepages/brian/audiodiy/mods/digi-out.htm).
The transformer T1 is high quality 1:1 pulse transformer (can be salvaged
from old broken network interface card or similar source).

Another S/PDIF output circuit

|\
+—–| O———–+
| |/ | S/PDIF output
| | 100nF (RCA or BNC)
| |\ | || T1
TTL level signal —–+—–| O———–+—||—-+ +——-+–75R— center pin
| |/ | || | | |
| | )|| | |
| |\ | 15 )||( 3 220R
+—–| O———–+ turns )||( turns |
| |/ | )|| | |
| | | | |
| |\04 | | +——-+——– ground
+—–| 0———–+ |
|/ —

74HCU04

This circuit is part of circuit “Splitter for S/PDIF coax/optical output” by T. Giesberts
from Elektor Electronics magazine July/August 1995 pages 78-79.
The transformer T1 is made to G2.3-FT12 ferrite ring core. Primary coil is 15 turns
of 0.5 mm diameter enamelled copper wire and secondary is 3 turns of 0.5 mm diameter
enamelled copper wire.
The chip 74HCU04 is manufactured by Philips

The circuit in the magazine had 3 outputs. The two extra output were made
by adding two more output coils to T1 and the output resistors.

Output circuit with transformer used as impedance matcher

This circuit is taken from Digital One V. 1.1 documentation.
Digital One is from NET-Labs and is designed by by Enland Unruh.

                                                               S/PDIF output

IC1 0.1 uF 0.1 uF
|\ || ||
TTL level signal ———–| +—–750R–+—||—-+ +–||— center pin
|/ | || | | ||
| )||(
| )||(
| )||(
| )||(
499R | |
| | +——- ground
+—-+—-+ T1
|

 

T1 is a HF-transformer which has 2:1 turns ratio.
Transformer type used in example circuit is SC944-05.
IC1 in this circuit consists of 8 parallel connected
buffer ports from 74ACQ244 IC.

Output with 1:1 pulse transformer

This is the recommended S/PDIF output circuit from
Crystal Semiconductor
CD4237 single chip multimedia audio system IC datasheet page 71.

                                                               S/PDIF output
                            IC1
                            |\
TTL level signal -----------| +-----374R--+---------+    +------- center pin
                            |/            |         |    |
                                          |          )||(
                                          |          )||(
                                          |          )||(
                                          |          )||(
                                       90.9R        |    |
                                          |         |    +------- ground
                                          +----+----+ T1
                                               |
                                              ---

 


The transformer used in this circuit is 1:1 pulse transformer
(the original application note suggested pulse transformer from
Pulse Engineering or Schott Corporation).
IC1 is a buffer IC which must be capablw to supply enough current
to drive the 75 ohm S/PDIF interface to full votlage swing specified
(capable of loading 415 ohm load or capable of supplying 12 mA current).

Simple S/PDIF output without galvanic isolation

|\
+—–| O———–+
| |/ | S/PDIF output
| | 150nF (RCA or BNC)
|\ | |\ | ||
TTL level —| o——+—–| O———–+—||—–374R—+—– center pin
signal |/ | |/ | || |
| | |
| |\ | 93R1
+—–| O———–+ |
| |/ | +—– ground
| | |
| |\ | —
+—–| 0———–+
| |/ |
| |
| |\ |
+—–| 0———–+
|/

74HTU04

 


This circuit does not provide any isolation on the output.
The TTL level signal form 74HCT04 buffer is attenuated to the levels
specified in S/PDIF optical interface by using the voltage divider
made of 374 ohm and 93.1 ohm resistors.
This circuit is based on S/PDIF converter circuit diagram from Elektor Electronics
magazine issue 4/1997 page 66.

Simplest TTL to S/PDIF coax interface

         100nF
  TTL ----||-----330ohm--+--------- coax S/PDIF signal out
  in                     |
                      100ohm
                         |
 Ground -----------------+--------- coax signal ground

This ricuit interfaces directly to the TTL level output
provided by some sound equipment (CD-ROM or soundcard).
This circuit works if the equipment which gives out TTL
level has powerful enough TTL output to run this circuit
(enough current output capability). If this simple
circuit does not work reliably, then you need to build
a circuit which includes the buffering electronics.

Isolation transformer for S/PDIF output

If your equipment (for example sound cards) has an S/PDIF output
which does not have an isolation transformer at the output, you
can easily add the transformer to it by putting a suitable
transformer afther the original output.

Elector Electronics magazine issue 7-8/1999 recommend building
the transformer for S/PDIF isolation in the following way:

The transformer must have good coupling factor, so the
transformer core must be a toroidal core made of high
permiability material. The prototype described in the magazine
uses Philips Type TN13/7.5/5-3E25 core which has permiability rating
(yt) of 4500. THe primary and secondary windongs consisted of 6 turns
of 0.5 mm diameter enamelled copper wire laid on opposite sides
of toroid. The transformer used in this prototype was described
to have a bandwidth raged from 50 kHz to 17 MHz, which is more
than adequate for an S/PDIF link.

The transformer should be fitted directly to the source and
the receiving end must be protperly terminated for reliable operation.
The reason for this is that the transformer input and output
impedances are not exactly 75 ohm.

S/PDIF input circuits

The following circuits can be used to convert S/PDIF
signals to TTL level signals which can be connected
to any suitable output circuit or directly to digital
electronics.

S/PDIF coax input circuit

+—-10K–+
10 nF | |
|| | |\ | |\
S/PDIF input ——+—||—-100R–+—-| O–+—+—-| O—– TTL out
| || |/ | |/
75R 10K
| 74HCU04 |
— —

 


This circuit is part of circuit “Splitter for S/PDIF coax/optical output” by T. Giesberts
from Elektor Electronics magazine July/August 1995 pages 78-79.
The chip 74HCU04 is manufactured by Philips

Another input circuit

+—-10K—– +5V
| /\
— |
4700 pF |
|| | |\ |\
S/PDIF input ———-||———-+—-| O———–| O—– TTL out
(+/-500mV) || |/ |/

7404

The capacitor works as DC blocking capacitor. 10 kohm trimpot
signal raises its ground potential to the point that Hex Inverter IC1 recognizes the
difference between a digital 1 and 0 input. When you firt test the circuit then
first addjust 10 kohm trimmer to the center and then adjust it so that the
circuit receivers the S/PDIF signal well. If you have a voltmeter, you
can adjust the trimpot to show around 2.6V at pin 1 of the IC.
The inverter buffers the input and produces TTL 0-5V output signal.
This circuit does not provivide the 75 ohm termination
resistor, so you need to add it if you have problems because of cable signal
reflections. This circuit is ppart of
Coax Digital Out to MD
circuit design.

Optical S/PDIF output circuit

Optical TOSLINK output

                        ________________
                      4|             ___|
 TTL signal -----------|            /
                       |           |
                      3|           |
 +5V--4R7--+-----------|           |
           |          2|   TOTX173 |
           +---8k2-----|           |
           |           |           |
          === 100 nF   |           |
           |          1|            \___
           +-----------|________________|
           |
          ---

 


The 4.7 ohm resistor and 100 nF capacitor make a filter against
digital noise in +5V power source.
The Toslink transmitting module used in this circuit is TOTX173 from Toshiba.
This circuit is a part of circuit diagram from Elektor Electronics
magazine issue 4/1997 page 65.

TORX173 and TOTX173 module pinouts

Toshiba optical receiver & transmitter modules used for S/P-DIF
TORX173, TOTX173 top view:

    opto
   +----+
  6.    .5
   +....+
    1234
Pin  TORX173     TOTX173
1    out         GND
2    GND         R
3    Vcc         Vcc
4    GND         in
5    case(GND)   case(GND)
6    case(GND)   case(GND)

Vcc +5V (use 0.1 uF decoupling to GND)
(use 47 uH choke to connect Pin 3 to Vcc for TORX)
R 8.2 kOhm to Vcc

TORX and TOTX are both high active and are CMOS/TLL logic compatible.

More information and datasheets is available at
Toshiba optoelectronics components web page TOSLINK section.

Very cheap optical S/PDIF output

With TOSLINK modules available for as low as $10 it hardly seems
worth it to bother with the trouble of making
your own TOSLINK module due to the fact that the ones from Sharp have a
built-in connector and are much easier to interface.
But if you really want to make your own optical output interface, you
can do it because S/PDIF optical (Toslink) transmitter is just basically
a red LED coupled to the optical fiber. So to build a very basic
output circuit you only need a red LED and a
resistor, both available from any place where electronic components are sold.

The circuit is very simple:

                   _____
TTL signal -------|_____|---------+
                                  |
                                 ---
                                  V  LED
                                 ---
                                  |
    Ground -----------------------+

The idea of the circuit is that the digital data is fed through
a series current limiting resistor to the LED (typically LEDs only require 5-30mA).
A digital 0 is 0V and the LED is off. A digital 1 is +5V and the LED is on.
That’s it!

If for some reason the circuit does not work, try to change the LED
and also try to connecting it better to the optical fiber.
NOTE: Not all LEDs will work, so you may have to experiment a bit.
Optimally, you want a high-brightness RED LED with a typical wavelength of 660nm.

If swapping the LED doesn’t work, you might want to try using a
hex inverter (7404 or similar IC) to buffer
the signal. This might be good practice too, just in case the TTL SPDIF
output of your source device isn’t designed to handle a 20~30mA load
this circuit generates.

Optical S/PDIF output circuit

Optical TOSLINK receiver

       _____________
      |___          |1
          \         |----------------- TTL output
           |        |
           |TORX173 |3
           |        |----+----coil47uH----- +5V
           |        |    |
           |        |   === 100 nF
           |        |2   |
           |        |----+
           |        |4   |
           |        |----+
           |        |5   |
           |        |----+
           |        |6   |
        __/         |----+
       |____________|    |
                        ---

The 47 microhenry coil and 100 nF capacitor make a filter against digital noise
in +5V power source.
The Toslink receiving module used in this circuit is TORX173 from Toshiba.
This circuit is a part of circuit diagram from Elektor Electronics
magazine issue 4/1997 page 66.

TORX173 and TOTX173 module pinouts

Toshiba optical receiver & transmitter modules used for S/P-DIF
TORX173, TOTX173 top view:

    opto
   +----+
  6.    .5
   +....+
    1234
Pin  TORX173     TOTX173
1    out         GND
2    GND         R
3    Vcc         Vcc
4    GND         in
5    case(GND)   case(GND)
6    case(GND)   case(GND)

Vcc +5V (use 0.1 uF decoupling to GND)
(use 47 uH choke to connect Pin 3 to Vcc for TORX)
R 8.2 kOhm to Vcc

TORX and TOTX are both high active and are CMOS/TLL logic compatible.

More information and datasheets is available at
Toshiba optoelectronics components web page TOSLINK section.


Other related information

Who makes AES/EBU digital audio transceiver chips ?

DSP FAQ mentions that Sony, Crystal Semiconductor, Motorola and
Yamaha have all AES/EBU tranceiver chips available.
DSP FAQ contain more
information about AES/EBU chips at http://tjev.tel.etf.hr/josip/DSP/FAQ/42.html.
Same companies which have AES/EBU chips have also SPDIF chips and some
chips can handle both formats.

Information sources

  • About SP-DIF by DJ Greaves
  • DSP FAQ
  • Elektor Electronics magazine July/August 1995 pages 78-79
  • Public domain S/PDIF document found in in the net (that article did not mention the author name)
  • David K. Fibush, Jitter Effect and Measurement in Serial Digital Television Signals, SMPTE Journal, August 1993, pages 693-698
  • Various articles from usenet newsgroups sci.electronics.design, rec.audio.pro and rec.audio.tech
  • Super-Cheap TOSLINK Module web page

Источник http://www.epanorama.net/documents/audio/spdif.html

1 comment for “S/P DIF ( s/pdif )

    --->

Добавить комментарий для S/PDIF цифровой выход пути улучшения - audioGO Отменить ответ

Ваш адрес email не будет опубликован. Обязательные поля помечены *